ASTM D6110 PDF

Charpy for ASTM D and ASTM D Testing and Izod Impact Testers for ASTM D, ASTM D and ASTM E23 Testing. ASTM D defines the method used to determine the resistance of plastic to breakage when impacted in a three point bend configuration, using a pendulum. ASTM D is used to determine the resistance of plastics to breakage by flexural shock as indicated by the energy extracted from standardized pendulum type.

Author: Kazira Maurg
Country: Mayotte
Language: English (Spanish)
Genre: Music
Published (Last): 17 February 2017
Pages: 329
PDF File Size: 3.67 Mb
ePub File Size: 3.44 Mb
ISBN: 890-6-15924-176-9
Downloads: 38202
Price: Free* [*Free Regsitration Required]
Uploader: Nalar

ASTM D6110 Charpy Impact Resistance of Notched Specimens of Plastics

The results are reported in terms of energy absorbed per unit of specimen width, or more specifically, the energy absorbed in breaking the specimen which is equal to the difference between the potential energy at the moment of 6d110 and the residual energy. The beam arm is mounted in frictionless bearings, providing high levels of reproducibility and repeatability. To meet the requirements of the standard we recommend our CEAST Pendulum — in either manual or motorized version, along with a specimen support vise, properly sized shoulders, and hammers.

Vibrational losses are observed when wide specimens of tough materials are tested in machines of insufficient mass, or in machines that are not securely fastened to a heavy base. Because of differences in the elastic and viscoelastic properties of plastics, however, response to a given notch varies among materials. To fully understand the test set-up, procedure, results and specimen preparation requirements, please refer to the standard.

One design of milled notch is allowed. D1610 2 for Dynamic Testing. It is the responsibility of the user of this standard asym establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Be aware that other differences in machine design do exist. Moreover, manufacturers aatm the equipment are permitted to use different lengths and constructions of pendulums with possible v6110 in pendulum rigidities resulting see Section 5.

  CARLO PELLICCIA ANDROID PDF

Electronic Charpy Impact Testing Equipment ASTM D – Plastic impact tester – United Test

Link to Active This link will always route to the current Active version of the standard. If breakage does not occur, a heavier hammer is asfm until failure occurs. By continuing to use ashm site, you accept our cookie policy. The notch produces a stress concentration which promotes a brittle, rather than a ductile, fracture. The hammer is released and allowed to strike through the specimen.

The specimen is mounted horizontally and supported unclamped at both ends. It is widely used in the industries of plastic products, plastic manufacture, petro chemical etc, University, scientific research institute and commodity inspection department.

In both the Charpy and Izod Tests, the notch produces a stress concentration which promotes a brittle, rather than a ductile, fracture. Note 3—Caution must be exercised in interpreting the results of this test method. How can we help you? It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining the Charpy Impact Resistance of Notched Specimens of Plastics This test method is used to determine the resistance of plastics to breakage by flexural shock as indicated by the energy extracted from standardized pendulum-type hammers, mounted in standardized machines, in breaking standard specimens with one pendulum swing.

Locating the striking nose precisely at the center of percussion reduces the vibration of the pendulum arm when used with brittle specimens. Email addresses can only contain letters, numbers and the following special characters: Please confirm that you agree with our privacy and cookies policy to submit this form.

The fact that a material shows twice the energy absorption of another under these conditions of test does not indicate that this same relationship will exist under another set of test conditions.

Supporting blade angle radius. The results of this test method are reported in terms of energy absorbed per unit of specimen 6d110 see Note 3. We use cookies to improve your browsing experience.

  ASKEP AKUT MIOKARD INFARK PDF

The pendulum is released and allowed to strike through the specimen. Supporting blade included angle. Pendulum center to specimen center distance. The beam arm is supported by a self indexing astk which is released by the operating lever. Impact values cannot be directly compared for s6110 two materials that experience different types of failure. Loadframe, pendulum 1J, 2J, 4J, 5Jsupporting vice jaws, specimen centering plate, spanner, power cord, manual etc.

The notch produces a stress concentration which promotes a brittle, rather than a ductile, fracture. Some losses due to pendulum arm vibration the amount varying with the design of the pendulum will occur with tough asstm even when the striking nose is properly positioned. Hammers of different initial energies produced by varying their effective weightshowever, are recommended for use with specimens of different impact resistance.

Email addresses must contain the symbol. Izod Tests on plastics, ceramics, glass, etc. The test is typically uninstrumented and is used to determine the energy required to break the specimen. Referenced Documents purchase separately The documents listed below are referenced aatm the subject standard but are not provided as part of the standard.

ASTM D6110 Determination of Charpy Impact Properties

Subscribe to Instron News! Bluehill LE for Basic Testing. The Dual Model features two large angular scales with 2 J graduations, the innermost for the Izod Test and the outermost for the Asm Test. If there is no material specification, then the requirements of this test method apply. The content is significantly different. Software for Series Systems.

Copyright Beijing United Test Co. Charpy and Izod Tests; IT30 0. The toss energy, or the energy used to throw the free ends of the broken specimen, is suspected to represent a very large d1610 of the total energy absorbed when testing relatively dense and brittle materials. Be aware that other differences in machine design do exist.

Author: admin